TREN
Contact us
R&D · DESIGN · MANUFACTURING · AFTERMARKET

From idea to series production: electronics and software.

Dramer offers R&D, design, manufacturing and aftermarket support for electronic products under one roof. From circuit boards to embedded software, from prototype to series production, we stay with your product all the way. Our deepest expertise: medical electronics.

See our services Talk about a project
* From our projects: master alarm interface · example view
R&Dhardware + softwareElectronics, PCB, embedded software and mechanical design
Prototype→ productionA smooth move from pilot runs to series production
Test+ traceabilityEvery unit tested and traced by serial number
SupportlifelongRepair, updates and obsolescence management
01 What we do

One partner for your product's entire life.

The teams that design, build and maintain an electronic product are often separate, and knowledge and time are lost at every hand-over. We run all three stages under one roof: we turn your idea into a design, the design into series production, and the product into a system that keeps working for years.

01 · WE DESIGN

R&D and design

From idea to working prototype: hardware, software and mechanics at the same table.

  • Product concept & specification
  • Electronics & PCB design
  • Embedded & enterprise software
  • Mechanical design
  • Testing & certification readiness
02 · WE BUILD

Industrialisation & manufacturing

A smooth move from prototype to series production; every unit tested and traced.

  • Pilot production
  • Series production management
  • Functional test & calibration
  • Supply chain & materials
  • Serial-number traceability
03 · WE SUPPORT

Aftermarket & lifecycle

We stay with you after launch and keep your product running for years.

  • Repair & refurbishment
  • Software updates
  • Obsolescence management
  • Spare boards & parts
  • Technical support
WHERE WE WORK Medical devicesHospital infrastructureIndustrial electronicsMeasurement & monitoringSoftware for manufacturers
02 R&D and design

Hardware, software and mechanics in one team.

We become your partner from day one. Because electronics, software and mechanical design run together, the pieces fit — and cost and time stay under control from the start.

01

Electronics design

Analog and digital circuits, power electronics, sensor interfaces and low-power designs.

02

PCB design

Multi-layer layout, signal and thermal control, design-for-manufacturing (DFM) review.

03

Embedded software

Microcontroller firmware, real-time applications, drivers and communication protocols.

04

Application & enterprise software

Device interfaces, monitoring dashboards, data acquisition and enterprise systems such as ERP.

05

Mechanical design

Enclosure design, 3D modelling, rapid prototyping and assembly-friendly structures.

06

Test & validation

Test fixtures, calibration, endurance and field tests; a test plan for every product.

07

Quality & certification

Risk analysis, technical files and support in preparing for CE and medical device regulations.

08

Project management

A single point of contact: planning, supplier coordination and regular progress reports.

SIMULTANEOUS ENGINEERING

We design with production in mind.

  • Sourceable partsWe choose long-life, available components.
  • Easy-to-build boardsLayouts follow series-production rules.
  • Test planned up frontTest points and fixtures are prepared with the design.
03 Manufacturing & aftermarket

From prototype to production, from production to the field.

Every product follows the same path. The team that designs it also follows its production and its life in the field, so no knowledge is lost at a hand-over.

  1. 01

    Idea & specification

    We define together what the product will do: function, cost, standards, timeline.

  2. 02

    Design

    Electronics, PCB, software and mechanical design; manufacturability check.

  3. 03

    Prototype

    First boards and enclosure are built and brought up in the lab.

  4. 04

    Validation

    Functional, endurance and field tests; certification preparation.

  5. 05

    Series production

    Pilot run, ramp-up, testing and traceability of every unit.

  6. 06

    Aftermarket

    Repair, software updates, spare parts and obsolescence management.

INDUSTRIALISATION & MANUFACTURING

From prototype to series production

  • Pilot productionA small first run to prove the process and the tests.
  • Series production managementPlanning and follow-up of board assembly, final assembly and packaging.
  • Functional test & calibrationEvery unit is tested one by one on its own fixture.
  • Supply chain & materialsComponent selection, purchasing and stock planning.
  • TraceabilityEvery board is recorded by serial number: which parts, which test, which delivery.
AFTERMARKET & LIFECYCLE

With you while the product is in the field

  • Repair & refurbishmentDiagnosis, repair and re-test of faulty boards.
  • Software updatesNew features and improvements delivered to products in the field.
  • Obsolescence managementEnd-of-life parts are spotted early; boards are redesigned when needed.
  • Spare boards & partsSpare stock planning for critical products.
  • Technical supportEngineering support for installation and use.
PWR SENSOR MCU 32-BIT COM K1 K2 LED · BUZZER DRAMER · DR-AK-01 · REV C
TOUCH A PART

Inside an alarm board

Our zone valve and master alarm boards share a similar structure. Hover over a part on the board or pick one below to see what it does.

04 Expertise · Medical gas

What do we measure in each gas?

Our deepest experience is in hospital medical gas systems: manifold control, zone valve alarms, master alarms and gas analysis sensors. Pick a gas to see what our sensors monitor on that line.

Oxygen (O₂)

Given directly to the patient. How much flows and how pure it is are the two most critical values.

LIVE EXAMPLE
PURITY99.6%
Flow ●
184L/min
Amount of oxygen flowing in the line
Purity ●
99.6%
How pure the oxygen is
Pressure ●
4.60bar
Line pressure
Why it matters? If purity drops, the patient gets less oxygen than needed; an unexpected rise in flow can point to a leak.

* Values on screen are examples; actual limits are set per project and the applicable standard.

05 Projects

Work we have delivered.

A selection of projects we took from design to series production and that are working in the field today.

Fully automatic medical gas manifold control unit
CLIENT · TECNOMEDIN SERIES PRODUCTION

Fully automatic medical gas manifold control unit

Control and routing boards that switch automatically between cylinder banks, monitor pressure and show it on screen.

  • Electronics design
  • PCB design
  • Embedded software
  • Series production
Zone valve gas alarm controller
CLIENT · TECNOMEDIN SERIES PRODUCTION

Zone valve gas alarm unit

Alarm board and software that monitor gas-line pressure on each floor and warn with sound and light.

  • Alarm board
  • Embedded software
  • Testing
  • Series production
MASTER ALARM MEDICAL GAS MONITORING PANEL ● ALL LINES NORMAL O₂ 4.60 A5 4.80 A8 7.80 N₂O 4.40 CO₂ 4.30 VAC -0.65 O₂OXYGEN AIR 5MEDICAL AIR AIR 8SURGICAL AIR N₂ONITROUS OXIDE CO₂CARBON DIOXIDE VACUUMSUCTION NORMAL ALARM SILENCE TEST
CLIENT · TECNOMEDIN THE FIELD

Master alarm panel

A central alarm gathering every warning from manifolds and zone valve boxes on one panel, with silencing and per-line alerts.

  • Hardware
  • Software
  • Display UI
O₂ PURITY 99.6 % AIR 5 · O₂ OIL MOISTURE CO₂
CLIENT · TECNOMEDIN THE FIELD

Medical gas analysis sensors

Sensor modules measuring flow and purity in oxygen; oxygen ratio, oil, moisture and CO₂ in medical air.

  • Sensor design
  • Calibration
  • Software
141263
CLIENT · TECNOMEDIN USE

Enterprise ERP application

An ERP that brings the company's whole workflow — from stock to production, sales to service — into one system.

  • Stock
  • Production
  • Sales
  • Service
erp · Production
ERP DashboardStockProductionPurchasingSalesServiceReports
Production · This week EXAMPLE SCREEN
OPEN WORK ORDERS14+3
BOARDS PASSED TEST12699%
CRITICAL STOCK3items
SERIAL NOBOARDSTATUS
DR-MA-2610-0412Master alarm board✓ Ready to ship
DR-KK-2610-1187Zone valve board✓ In stock
DR-SN-2610-0093O₂ purity sensor◷ Calibrating
DR-SK-2610-0251Manifold control board✓ In assembly
06 Software & ERP

Software from inside the board to running the factory.

On one side we develop the embedded software running on the boards; on the other, the ERP applications manufacturers run their whole business on. Because we know both, the device in the field and the record in the office speak the same language.

  • Stock and material tracking with low-stock warnings
  • Production work orders and serial-number traceability for every board
  • Quotes, sales and shipping
  • Service records and reports
air5_check.cEXAMPLE
// Medical air quality check
void air5_check(reading_t *m) {
  if (m->o2 < 20.4 || m->o2 > 21.4) alarm(AMBER, "O2 ratio");
  if (m->co2 > 500)  alarm(AMBER, "CO2");       // ppm
  if (m->h2o > 67)   alarm(AMBER, "Moisture");  // ppm
  if (m->oil > 0.1)  alarm(AMBER, "Oil");       // mg/m3
}
07 About us

An engineering team that develops electronic products end to end.

Dramer Medical Electronics & IT offers the entire lifecycle of electronic products — from R&D to series production and aftermarket support — under one roof. At our office in the Sankara Brain and Biotechnology Research Center in Avcılar, Istanbul, we bring together hardware, embedded software, enterprise software and test engineering.

Our deepest expertise is medical electronics: control boards, alarm systems and measurement sensors for hospital gas systems. We bring the rigour we learned there to every project.

Dramer
LEGAL NAME
Dramer Medikal Elektronik ve Bilişim Hiz. San. ve Tic. Ltd. Şti.
ADDRESS
Üniversite Mah. Sarıgül Sk. Sankara Beyin ve Biyoteknoloji Araştırma Merkezi No: 35/1 İç Kapı No: 1, Avcılar / Istanbul, Türkiye
TAX OFFICE / NO
Avcılar Tax Office · 313 148 4696
01

One roof

Design, software, production and aftermarket in one team — responsibility never gets lost.

02

Medical-grade rigour

We apply the discipline of life-critical systems to every project.

03

R&D in Istanbul

Boards and software are designed in-house by our own team.

04

Long-term support

Updates, repairs and parts for as long as your product is in the field.

08 Contact

Let's talk about your project.

Planning a new product, a redesign of an existing one or series production? Tell us briefly and we'll get back to you as soon as possible.

E-MAILinfo@dramer.tr ADDRESS · OPEN MAPÜniversite Mah. Sarıgül Sk. No: 35/1 İç Kapı No: 1, Avcılar / Istanbul

Write to us

When you press Send, your e-mail app opens with your message ready.

Topic